Since ancient times, solid wood was used to build a bathhouse, which, when heated, released phytoncides, thereby suppressing the development of various pathogens. The Russian stove was considered one of the main elements of such a bathhouse. But with the development of modern technologies, it is often replaced by IR emitters. In just a few years, infrared heaters have become one of the most popular and sought-after types of heating. But, nevertheless, when choosing this equipment, many questions arise, therefore, when buying an infrared heater for a bath, it is worth considering in more detail not only the types of devices, but also their advantages. Our review will provide maximum assistance in this.
Photo: https://strport.ru/
Content:
- Infrared emitter Harvia Comfort
- Infrared emitter IRS 3 IR
- Infrared emitter Harvia Basic
- Infrared emitter IR-MAT IRF
- Infrared emitter VITAE
- Infrared emitter EOS IRS 3 IR
- Ceramic infrared emitter flat ECP-3 (60×60 mm)
- Set of IR emitters SteamTec TOLO B1
- Infrared emitter Vitae Protect
- Ceramic infrared hollow emitter ECH-2 (122×60 mm)
Infrared emitter Harvia Comfort
Photo: pokupki.market.yandex.ru
The HARVIA Comfort infrared radiator is a pleasant heat source that does not require any special maintenance. It warms up the body and allows you to enjoy this unique bathhouse even in a small apartment. The front panel of the HARVIA Comfort IR emitters is covered with soft, pleasant pile. The word Comfort in the marking of this series means that they are equipped with backlight. The HARVIA Comfort infrared emitter meets the strictest European safety and quality standards.
Infrared emitter Harvia Comfort
Advantages:
- Quality
- Safety
- Compliance with international standards
- Built-in wall
- Protective covering
- Reflector – aluminum
- Heating element – stainless steel
- Availability of backlight
Advantages and disadvantages
The uniform and deeper heating of the human body, which is carried out by an infrared sauna, ensures that the result of its session provides the maximum effect for the body. The main aspects confirming the beneficial qualities of the procedures are the following:
- Good tolerance. As a result of low temperatures and normal humidity, there is no physical discomfort.
- Possibility of receiving a thermal session at any convenient time. Without preliminary preparation (heating) of the room.
- A similar criterion is associated with the short time required to conduct a standard session.
- Easy to use, mobile. Installing an infrared sauna does not require a lot of free space, and even a child can handle the controls.
- Safety of use, since the likelihood of getting a burn is minimized.
Execution of a combined sauna Source spa-system.ru Double IR sauna Source sc01.alicdn.com Benefits of IR cabins for the human body Source sc01.alicdn.com
Inside the device, in a relatively short period of time, you can undergo useful warming, which will contribute to:
- Removing excess fluid and metabolic products (metabolism). Normalization of the level of water balance (the ratio of the amount of fluid entering the body and removed from it in the same period of time).
- Antibacterial effect, helping in the fight against colds.
- Improving blood circulation throughout the body.
- Saturation of body cells with oxygen and beneficial microelements.
- Normalization of metabolism.
- Reducing the content of “sticky” (bad) LDL cholesterol and increasing the amount of “good” (HDL) cholesterol, which has a beneficial effect on heart function.
Infrared cabin for three Source fitowood.ru
Infrared emitter IRS 3 IR
Photo: pokupki.market.yandex.ru
The infrared emitter EOS IRS 3 IR is designed for infrared cabins. The ceramic heating element with a spiral is made of high quality aluminum. The body of the product is made of galvanized steel. Thanks to the protective grid on the device, the possibility of burns during use is eliminated.
Infrared emitter IRS 3 IR
Advantages:
- Ceramic heating element
- Aluminum spiral
- Galvanized body
- Protective grille
- Quality, safety
Infrared emitter Harvia Basic
Photo: pokupki.market.yandex.ru
The powerful and reliable infrared emitter HARVIA Basic is a typical example of the products of this brand. It combines modern requirements for the safety and efficiency of equipment and long-standing traditions in the production of sauna equipment. The gentle warmth of the IR emitter allows you to enjoy a sauna at home. The HARVIA Basic infrared emitter has a front panel covered with soft bristles. It fits neatly into the cabin and is in fact its main element. Basic models are produced without illumination, this is worth considering when choosing an IR emitter for a sauna. The unit is controlled from a remote control.
Infrared emitter Harvia Basic
Advantages:
- Soft warmth
- Accuracy
- Reliability
- Economical
- Protective covering
- Stainless steel heater
- Built-in wall
- Remote control
Infrared emitter IR-MAT IRF
Photo: pokupki.market.yandex.ru
Panel IR emitters are usually mounted behind a wall and distribute the radiation they produce evenly. They take some time to heat up, and their radiation travels in the long-wave range.
Infrared emitter IR-MAT IRF
Advantages:
- Even heat distribution
- Built-in wall
- Short heating time
- Quality of use
- Safety, reliability
Rules for using the sauna
The recommended duration of the procedure is half an hour. At this time, you cannot leave the cabin, but you are not forbidden to open the door. The position should be comfortable, legs down, back straight.
- The sitting position is most optimal. To prevent dehydration, drink water.
- Experts advise visiting the sauna no more than twice a week.
- After relaxation, do not use a cold shower, only warm water.
- Before going inside, remove makeup and wash your body.
Do not manipulate lotions, creams and scrubs, because an allergic reaction or burn is possible. Light food is consumed an hour before the visit.
Wipe off sweat with a dry towel, otherwise heating will slow down. At the end of the session, relax and drink green tea. It is required to keep the room clean, do not pour liquid, use a bactericidal lamp and do not ignore operating recommendations, which will cause damage to the goods.
Infrared emitter VITAE
Photo: pokupki.market.yandex.ru
Infrared emitters of the Vitae series have several power variations of the glass-ceramic heating element. This is the most common type of emitter. At the moment, these emitters have radiation that is closest to solar heat. And thanks to a specially designed reflector, useful infrared radiation is distributed as widely as possible. All IR heaters are equipped with plugs for easy connection to the control system. The decorative protective casing is coated with a special material, thus eliminating the possibility of burns. Also, one of the most important advantages of Vitae IR heaters is that they do not require warm-up time. They immediately begin to radiate heat.
Infrared emitter VITAE
Advantages:
- Glass ceramic heating element
- Emission in the range of 1.4–10 μm
- Possibility of installation both in the wall and in the corner
- Connection cable included
- 500–750 W with switching current limiter
- Connection – 230 VN AC 50 Hz
- Dimensions – 870 x 184 x 65 mm
- Instant warm-up
Additional criteria
If you are serious about choosing a sauna stove, pay attention to additional parameters that may affect the convenience and performance of the unit:
- The volume of the heater determines the number of stones that can be used during bath procedures. The fewer stones, the faster they will warm up, but also cool down faster. This parameter should be assessed individually - if you do not plan to wash and steam for a long time, choose models with a small heater volume.
- Type of heater - open or closed. In the first case, the air in the sauna will heat up faster, and the steam will be more aggressive. A closed-type heater is considered gentle, emitting soft, comfortable heat - the stones here are covered with metal walls, gratings or meshes.
- The source of steam is traditional and forced. In order to create steam in a conventional sauna stove, it is necessary to water the stones from time to time. But with this method it is difficult to control the level of humidity and achieve a comfortable microclimate. In devices with forced steam generation, an additional element is provided - a steam generator, which allows you to control humidity. It heats up faster than stones, saturating the space with the necessary steam while maintaining a comfortable air temperature.
- Efficiency and heating rate. The metal stoves included in this rating are characterized by accelerated heating - they reach maximum temperature parameters in an average of 30 minutes. The heating rate is also affected by the capacity of the firebox, the volume and type of heater - we mentioned above how to choose a stove for a sauna according to these criteria.
When choosing a stove for a sauna or bathhouse, first of all take into account the dimensions of the steam room for which you are purchasing the unit.
Then consider the design features - the location of the firebox, the presence of a heating tank, a steam generator, the type of heater. Don’t forget to inquire about the heating speed and fuel consumption - the device must be highly energy efficient. Return to list of articles
Infrared emitter EOS IRS 3 IR
Photo: pokupki.market.yandex.ru
IRS 3 occupies a significant place in the EOS line of IR heaters. Structural elements and reflectors are made of polished high-quality stainless steel. The heating element is a ceramic rod. Ceramic heaters are more productive than aluminum ones; the heat they emit penetrates deeper into the human body. Possibility of installation both in the wall and in the corner.
Infrared emitter EOS IRS 3 IR
Advantages:
- Use of stainless steel
- Ceramic heating element
- High performance
- Installation versatility
- Safety, reliability
- Emission in the range of 2–10 μm
- Connection cable included
- Connection – 230 VN AC 50 Hz
- Dimensions – 530 x 185 x 75 mm
Reflectors
- IR energy is effective if it hits the human body. Outside its location, heating is a consequence of the internal temperature of the room. Reflectors are used precisely for this purpose; they disperse the radiation very much.
- The reflector is a curved metal plate with reflective properties. This allows you to direct up to 95% of the emitted energy to the object. The reflector models correspond to the emitters of clay heaters, for example, the ECS-2, ECP-2, ECH-2 emitter corresponds to the ECR2 reflector.
- The wide shape of the reflector helps soften and distribute the radiation at an angle of approximately 120°. Such models are used in small-sized cabins, so that for a person sitting close to the heater, the radiation is pleasant.
- Corner reflectors operate differently, namely: they concentrate the rays at an angle of 90°. For the most part, they are installed in spacious saunas, focusing IR radiation onto the bench.
Ceramic infrared emitter flat ECP-3 (60×60 mm)
Photo: pokupki.market.yandex.ru
ECP series ceramic electric infrared emitters are manufactured with a flat emitting surface that directs the rays perpendicular to the heater surface, allowing uniform heating to be achieved over a limited surface area. Still don't know what is the best infrared heater for a sauna and how to choose it? Then you should take a closer look at this design.
Ceramic infrared emitter flat ECP-3 (60×60 mm)
Advantages:
- Flat radiating surface
- Uniform heating
- Local action
- Quality guarantees
- Reliability
- Safety
Necessary tips
- Infrared heaters must be placed so that a single thermal field is created, thereby achieving uniform heating of vacationers. Almost always there are enough 6 devices per room, two of which are installed on the back wall, one each on the side surfaces or in the corners, above the door, and one is installed horizontally in the canopy riser for heating the feet. The devices are located vertically, due to the fact that a person is almost always in a sitting position indoors.
- The heater power is selected based on the area of the room. This is explained by the fact that the device is recommended not for heating air, but for heating the surfaces of the room and the objects (people) in it.
- Emissivity indicates how much energy is dissipated. The higher the value, the better. For example, if the coefficient is 80%, it means 20% thermal energy.
- Ceiling height is the main aspect when selecting models; for example, it is not recommended to install a low-power heater in a room where the ceiling is about four meters. In this case, the rays never reached the floor.
- On the contrary, it is not recommended to install an excellent device with ceilings whose height is less than 2.7 m; the person in such a room will experience inconvenience associated with excess thermal radiation.
Set of IR emitters SteamTec TOLO B1
Photo: pokupki.market.yandex.ru
The SteamTec TOLO B1 set of IR emitters can equally well act as a stand-alone system or as an additional option for steam generators of the TOLO model line. If the kit is used independently, operating time and power are controlled using the included control panel. If the kit is installed as an additional option to the steam generator, then the operating parameters are controlled using one remote control. The set of IR emitters SteamTec TOLO B1 consists of five emitters capable of maintaining a temperature of 60 degrees Celsius, as well as an acoustic system, control panel, distribution block, and connecting cables. All included parts are made taking into account the parameters of the microclimate prevailing in the steam room, and have a high level of protection against contact with air supersaturated with moisture, temperature changes and accidental splashes. The housings of the emitters are made of high-quality ceramics and framed with cedar wood, which gives them a more attractive appearance.
Set of IR emitters SteamTec TOLO B1 (5 ceramic infrared emitters with cedar frames, remote control, USB/MP3 acoustics with speakers)
Advantages:
- Availability of remote control
- Availability of an acoustic system
- 5 emitters included
- Temperature maintenance 60°C
- Compliance with the microclimate of the steam room
- Protection from moisture and accidental splashes
- Resistance to temperature changes
- High quality ceramic body
- Attractive appearance
Criterion #2: Fuel Type
Which stove to install in your sauna will largely depend on the type of fuel available in your location. Heating devices, depending on the modification, are capable of operating on:
- natural gas;
- electricity;
- liquid fuel;
- solid fuel.
The last option is considered the most popular, cost-effective and practical. Well-dried firewood or pressed sawdust pellets are used as fuel.
Important! Wood-burning stoves do not require additional installation of communications, create a minimum of carbon monoxide, and do not depend on electricity and gas supplies.
Wood burning heater Rolling Stones v.2
Characteristics:
- steam room volume – 26 m3;
- fuel type – firewood, pellets;
- door – panoramic made of tempered glass;
- weight of stones – 100 kg;
- firebox material – steel;
- heater type – open;
- chimney diameter – 115 mm;
- stove weight – 120 kg.
Price in our online store – from 28,652 ₽.
Product link: https://sadpom.ru/products/drovyanaya-pech-kamenka-rolling-stones-v2/
The wood-burning stove from the manufacturer Greivari is distinguished by its high reliability and robust design. Alloy steel 6 mm thick ensures increased wear resistance of the walls of the smoke collector and deflector, and special ash pads protect the bottom of the device from overheating. The impressive volume of the firebox allows you to load a large amount of firewood and heat a room with a volume of up to 26 m3. Thanks to the inclined bottom, it is impossible to accidentally fill the laid stones with water, and due to hot convection currents, you can count on maximum heating of the stone backfill.
Installation advantages:
- secondary combustion system for efficient fuel combustion;
- convenient cleaning hole;
- durable materials;
- light steam
Flaws:
- relatively high cost;
- long heating of stones.
Back to Contents
Infrared emitter Vitae Protect
Photo: pokupki.market.yandex.ru
New infrared emitter for private and commercial IR cabins. High-performance emitter with a quartz glass heating element, covering the entire range of useful infrared radiation. Vitae Protect is equipped with a durable housing, a protective grille, an installation cable and a diffusion glass screen that prevents moisture from entering the inside of the emitter. The equipment complies with IPX4 protection class.
Infrared emitter Vitae Protect
Advantages:
- Quick start without pre-warming
- High intensity and wide heating angle
- Full spectrum of IR radiation – IR-A, IR-B and IR-C / 0.8 – 10 μm
- Dimmable using suitable control systems
- Power: 350 / 500 / 750 W
- Durable stainless steel housing
- Polished aluminum reflector
- Glass-ceramic safety glass
- Equipped with built-in surge protection
- 3m silicone cable included
- Dimensions (H x W x D) – 985 x 198 x 60 mm
- Connection: 230V 1N AC 50 Hz
- Installation: on walls and in corners of the cabin, vertically or horizontally
- Made in Germany
Ceramic infrared hollow emitter ECH-2 (122×60 mm)
Photo: pokupki.market.yandex.ru
Hollow IR emitters ECH with a cavity filled with air have a slightly higher heating temperature. Because of this, to achieve the heating temperature of the material required for the technological process, you will need much less power of the heating element, which will lead to savings in energy consumption. Power characteristics from 75 to 500 W, supply voltage 220 V, overall dimensions width 122 mm, height 60 mm, type of connection to the electrical network “heat-resistant wires with bead insulation.” The manufacturer guarantees the quality of manufactured heaters.
Ceramic infrared hollow emitter ECH-2 (122×60 mm)
Advantages:
- Saving energy consumption
- Heat resistant wires
- Quality assurance
- Low case heating temperature
- Efficiency
- Reliability
- Safety
#Top 10
Read us first - add the site to your favorite sources.
Add a comment
{"commentics_url":"\/\/express-novosti.ru\/comments\/","page_id":1245285,"enabled_country":false,"enabled_state":false,"state_id":0,"enabled_upload": false,"maximum_upload_amount":3,"maximum_upload_size":5,"maximum_upload_total":5,"securimage":true,"securimage_url":"\/\/express-novosti.ru\/comments\/3rdparty\/securimage\ /securimage_show.php?namespace=cmtx_1245285″,”lang_error_file_num”:”\u041c\u0430\u043a\u0441\u0438\u043c\u0443\u043c %d \u0444\u0430\u0439\u043b\u043e\ u0432\u043c\u043e\ u0436\u0435\u0442 \u0431\u044b\u0442\u044c \u0437\u0430\u0433\u0440\u0443\u0436\u0435\u043d\u043e.","lang_error_file_size":"\u041f\u043e \u0436\u0430\u043b\ u0443\u0439\u0441\u0442\u0430, \u0437\u0430\u0433\u0440\u0443\u0437\u0438\u0442\u0435 \u0444\u0430\u0439\u043b \u0440\u0430\ u0437\u043c\u0435\u0440\u043e \u043c \u043d\u0435 \u0431\u043e\u043b\u0435\u0435 %d MB.","lang_error_file_total":"\u041e\u0431\u0449\u0438\u0439 \u0440\u0430\u0437\u043 c\u0435\u0440\ u0432\u0441\u0435\u0445 \u0444\u0430\u0439\u043b\u043e\u0432 \u0434\u043e\u043b\u0436\u0435\u043d \u0431\u044b\u0442\u044c \ u043d\u0435\u0431\u043e\u043b\ u0435\u0435 %d MB.","lang_error_file_type":"\u041c\u043e\u0436\u043d\u043e \u0437\u0430\u0433\u0440\u0443\u0436\u0430\u0442\u044c \u0442\u0 43e\u043b\u044c ""lang_text_loading":" u0437\u043a\u0430 ..","lang_placeholder_state":"\u0420\u0435\u0433\u0438\u043e\u043d","lang_text_country_first":"\u0421\u043d\u0430\u0447\u0430\u043b\u0430 \u0432\u044b\u04 31\u0435 \u0440\u0438\u0442\u0435 \u0441\u0442\u0440\u0430\u043d\u0443″,”lang_button_submit”:”\u0414\u043e\u0431\u0430\u0432\u0438\u0442\u04 4c","lang_button_preview":" \u041f\u0440\u0435\u0434\u0432\u0430\u0440\u0438\u0442\u0435\u043b\u044c\u043d\u044b\u0439 \u043f\u0440\u043e\u0441\u043c\u 043e\u0442\u0440″,”lang_button_remove ":"\u0423\u0434\u0430\u043b\u0438\u0442\u044c","lang_button_processing":"\u041f\u043e\u0434\u043e\u0436\u0434\u0438\u0442\u0435..."}
