What to do if there is no draft in the stove - possible causes and solutions to problems

Let's take a closer look at why there is no draft in the stove or chimney of a private house or bathhouse, and what to do. Let's find out how to determine the presence of this problem and what to do to fix it.

Draft is the force of movement of exhaust gases along the outlet channel, appearing due to the difference in air temperatures. If it is normal, combustion products freely go outside; if there is not enough of it (or it is completely absent), gases accumulate in the pipe and either clog the hose, gradually reducing its throughput, or flow back into the room. This is dangerous because the smoke contains harmful substances that can cause poisoning.

The following signs will alert you to problems:

• the appearance of smoke when opening the cleaning door;
• smoke from pipes;
• pops of smoke masses on the stove door.

Useful information about chimney draft

All residents of country or private city houses are familiar with the concept of chimney draft. Do they know the essence of this term?

If we move a little away from the dry scientific terminology, then draft can be defined as a natural phenomenon in which air moves from one area to another, namely, from an air zone with high pressure to a zone with low pressure. All this happens with the help of a ventilation device - a special channel in the chimney.

Using this process of aerodynamics, humanity began to use fireplaces, stoves, boilers, heating their homes using different types of fuel - coal, firewood, peat, etc.

With good draft, the stove lights up quickly and the room is filled with pleasant warmth.

The following depends on a properly designed and constructed chimney and, accordingly, on good draft:

• quality of room heating;
• reduction in fuel costs;
• safety in buildings with their own heating.

What influences the value

There are three groups of factors that must be taken into account when constructing and inspecting a chimney.

In-house moments

A number of factors indoors can significantly influence the presence/absence of draft and its strength:

1. The material from which the building is constructed.
2. Average room temperature.
3. The maximum volume of air space in the home.
4. The number of people permanently staying inside the dwelling.
5. The presence of internal sources that additionally consume oxygen (heaters, heaters, stoves, etc.).
6. Regular supply of fresh air (airing, ventilation).

External factors

There are other factors that determine the chimney draft, and they are located outside the heated room. We are talking about external temperature, atmospheric pressure, humidity, wind direction. A phenomenon such as changing temperatures during the day can also affect draft - due to the movement of cold and warm layers of air.

Difficulties with traction appear for various reasons, some may simply not be noticed. For example, problems with air outlet through the chimney may arise if the pipe is located much lower than the ridge of the building or tall nearby trees.

Chimney design features

The draft may vary depending on the design characteristics of the chimney:

• height;
• presence of insulation;
• tightness;
• location (internal/external);
• length;
• presence/absence of irregularities or roughness, etc.

It is necessary and possible to control the draft in a room using the “levers” of the first and third factors (intra-house and design). Natural changes, of course, do not depend on humans.

Keeping the draft in the chimney under control is a prerequisite for safe and comfortable living in your own premises. If the draft is very weak, then it is almost impossible to light the stove and heat the home.

With reverse draft, the gases generated as a result of combustion are “thrown” into the living space, and not into the air through the pipe. This is very dangerous for human health and life!

It is impossible not to notice this atypical behavior of smoke

With very strong draft, all the heat is rapidly drawn out through the chimney channels, without having time to warm the heated room to the desired temperature.

The stove in the bathhouse is smoking, what to do: tips

Traction stalls occur for a variety of reasons. It is impossible to immediately determine what exactly led to the smoke. But there are several simple proven methods:

• first, ventilate the bathhouse in order to equalize the air temperature and pressure inside and outside the building, because if the flat roof of the bathhouse gets too hot, this leads to the draft overturning;
• mechanical obstacles - when igniting the stove, the damper must be open, as well as the vents on the chimney, if any, an overfilled combustion chamber or ash pan also does not allow creating draft, a snow cap on the chimney will also not allow the heater to light;
• to generate draft, they achieve rarefaction of the air inside the pipe; to do this, it is enough to burn a little paper in the firebox.

Important! To warm up the chimney or create a vacuum, do not use liquid flammable materials such as gasoline or kerosene. Otherwise a fire is inevitable

Why does reverse draft occur?

Weak thrust can become the basis for the formation of reverse thrust. How can you recognize that all is not well with cravings?

This is “spoken” by moments that can be seen with the naked eye: a lot of smoke in the stove, soot on the door, incoming smoke movement inside the house. In other words, smoke and fumes from the burning fuel do not go into the chimney through the chimney, but tend to enter the living space when the door is open and through cracks.

Causes of backdraft:

1. Design flaws of the chimney. A low pipe means an increased risk of reverse draft. The higher the pipe, the better the process of extracting exhaust gases and smoke. The optimal pipe height is about five meters .
2. Correspondence of the pipe diameter to the parameters of the furnace device. A powerful stove requires a chimney with a pipe of rather large cross-section. But the measure here is very important, because using a pipe that is too wide will make the combustion process unprofitable (all the warm air will literally fly into the pipe). It is unacceptable to use several pipes with different cross-sections in the chimney!
3. Use of non-smooth pipes. Unevenness, chips, roughness, etc. are an obstacle to good traction. Over time, the chimney opening may narrow due to soot deposits and other combustion elements and complicate the process of lighting the stove and its normal functioning.
4. Poor/lack of ventilation. Drafts and open windows in rooms located above the firebox do not help the fuel combustion process, but distort it, making it useless and unsafe.

Chimney channels made of metal are in many ways inferior to brick pipes. Rapid heating and equally rapid cooling are not good for the heating system in general and the chimney in particular.

Brick pipes are much more effective in terms of smoke extraction

Reverse thrust can also appear for objective reasons beyond a person’s control. Strong gusts of wind, rainy, cloudy weather with high humidity are unfavorable moments in terms of the formation of problems with traction.

There is such a term as temporary backdraft. What is this? In this case, it is worth talking about temporary traction disorders, lasting for several days. After a certain period, cravings return to normal.

Temporary reverse draft can occur due to a cold room that has been unheated for a long time. Very cold air accumulated in the chimney pipe prevents the fuel from burning quickly. Therefore, smoke can be “pushed” out of the chimney into a home, bathhouse or other room with a stove or fireplace.

It is very easy to eliminate cold air in the chimney - warm up the pipes by burning ordinary newspapers, wallpaper, and paper in the oven. The main thing is that these materials are well dried.

If problems with traction can be detected constantly or with a certain frequency, then it is necessary to take measures to eliminate bad traction.

Why increase efficiency?

The compact dimensions of the stove mean that the surface that heats up during operation is small. Not much heat flows outside and the room quickly cools down. Sometimes it seems that the return from the potbelly stove is weak.

To help it increase efficiency, several tasks are solved:

• the duration of combustion and smoldering increases;
• a sufficiently high combustion temperature is ensured;
• a high level of traction is achieved.

to contents

Improving heat transfer using fuel

A metal stove is heated in different ways: from wood to sawdust with small debris. To improve heat transfer in a potbelly stove, compressed sawdust, briquetted industrial waste and coal are used.

• Compressed sawdust burns out much more slowly - one load is enough for many hours of smoldering.
• Briquettes are made from wood shavings and waste. The pressed composition allows them to smolder for a long time, because they cannot flare up. Briquettes smolder evenly and for a long time, increasing the heat transfer of the potbelly stove.

It is also worth assessing the traction force. This can be done by looking at the color of the flame. If there is not enough air, the flame turns red and dark stripes appear; if there is too much oxygen, the flames become bright white. The draft , and with it the efficiency of the stove, is normal when the flame is golden-orange. For better traction, you can blow the potbelly stove using a conventional fan.

Using additional coolant

The stoves are complemented with water tanks and so-called water jackets in order to use them as an additional coolant and save energy.

The water jacket is designed as follows. A U-shaped tank in which water is heated is mounted in the housing. Two pipes branch off from the tank: for supply and processing. The tank itself is fed by tapping into the pipeline.

Sandbox

If you have no desire at all to re-equip your stove, add anything to it, or experiment with different types of fuel, there is the simplest and most economical method. A box is placed on the potbelly stove, in which two buckets of sand are placed.

Place 2 of these buckets in a box on top of the stove.

Brick screen around the stove

The brickwork around the device allows you to retain heat and protect yourself and others from contact with hot metal. Properly placed masonry increases heat transfer by about a quarter. When the potbelly stove is heated, the brickwork heats up. After the fuel burns, it will continue to share the collected heat. Experts advise laying bricks not close to each other, but 30 centimeters from the walls of the firebox.

To lay out the screen, you will need a couple of dozen heat-resistant bricks:

• the screen is laid out on clay mortar;
• the first row is laid out according to the intended markings;
• in the second row, ventilation gaps are made the size of half a brick;
• the brick is laid out in accordance with a pre-designed shape and size for the opening;
• A steel strip is attached to the last row for additional fixation.

Strength check

Before you try to fight bad traction, make sure that your traction really leaves something to be desired.

You can check the traction using special devices or yourself. Simple ways to fix traction:

1. Light a piece of paper and let it burn for a while. When you bring it to the stove or fireplace, extinguish the paper and observe the direction of the smoke. If it is directed towards the pipe - good thrust, deviates in the opposite direction - reverse thrust, if it remains “straightforward” - there is no thrust. Similar manipulations can be done with thin tissue or toilet paper without setting it on fire.
2. If there are smokers in the house, then follow the direction of the cigarette smoke or the flame of a match or lighter near the fireplace or stove. Draw conclusions similar to the first point.
3. The flame of an ordinary candle can also help in determining the draft in the home.
4. A pocket mirror brought to the firebox and covered with condensation may indicate problems with removing smoke from the stove.
5. The presence of too much draft, which carries away useful heat from the room, is indicated by an audible hum in the stove - a loud hum.
6. The color of the fire in the firebox can be an indicator of different drafts. A golden hue means good draft, white flame means excessive draft, red color and black smoke means poor draft, high probability of reverse draft.

A regular lighter can help test traction

An anemometer is a device familiar to many people of the Soviet period. Using this device it was possible to measure the draft of the chimney. Readings within 10–20 Pa were considered normal. The disadvantages of the device are its low accuracy when the wind force is less than one meter per second.

This simple device will help protect your life in a stove-heated home.

Modern industry offers a sufficient number of devices for measuring draft; there are devices that record draft at the inlet and outlet of the chimney.

Rose of Wind

A situation when the prevailing winds blow directly into the chimney and reduce the draft or reverse it. The chimney is installed on the windward side, of course, if the wind directions are determined. If the chimney is located far from the ridge and below, the leeward side cannot be used. Multi-storey buildings and trees also affect traction. To compensate for gusts of wind and poor placement of the chimney, anti-wind deflectors are used. According to the standards, the chimney is installed half a meter above the ridge. If the distance from the ridge is 1.5 m - 3 m, then it is brought to the same level as the ridge. If the distance is more than 3 meters, then proceed according to the formula: from the horizontal drawn from the ridge, 10 degrees down. In practice, the chimney is made higher than the ridge, or at the same level as the ridge

It is important to use one chimney for one stove in the house

Troubleshooting Methods

If you have identified problems with traction, then, of course, they need to be eliminated as quickly as possible.

The choice of means to combat poor or reverse draft depends on the reasons that led to the abnormal operation of the chimney.

Pipe cleaning

One of the common methods of improving traction is cleaning the pipe. Fuel, burning in a stove, releases various substances that settle on the inner surface of the chimney. Soot sticks well to pipes if they are uneven or bent.

When carrying out work, do not forget about safety measures

How to clean a chimney so that there is good draft?

First of all, acting purely mechanically. The chimney channels can be made wider, getting rid of plaque, in the following ways:

1. After preparing about one bucket of potatoes, peel and cut them. Potato peelings will also work. Throw a little into the firebox and wait. When burned, potatoes will release starch, which will become a means that can soften carbon deposits. Soft pieces of soot will fall off on their own, but firmly stuck ones will have to be removed mechanically.
2. Firewood from aspen. Heat the stove with two or three logs. They will heat up the chimney pipes very much and help get rid of carbon deposits. But this method requires special care, since the likelihood of a fire will be very high (soot may ignite).
3. Rock salt. This method is more suitable for prevention. Salt added at the time of combustion improves the condition of the chimney pipes.
4. Pipe brush. A heavy weight is attached to a brush suspended on a steel rope and lowered into the chimney openings. By lowering and raising this structure, you can force soot formations to fly off the walls of the pipes and fall into the furnace. These fragments are then removed from the firebox.

The second group of anti-particulate measures is based on the use of chemicals. The most popular chemicals for cleaning chimneys are “Log-chimney sweep”, “Komichek”. Chemicals are added to the coals formed during the heating of a stove or fireplace according to the instructions and the heating continues. After all the fuel has burned out, it is advisable to leave the coals, since they continue to “work” in terms of cleaning the chimney (at least, that’s what the manufacturers advise).

When used correctly, chemicals will not cause harm to your home.

Do not believe the spiteful critics who talk about the obligatory combustion of soot when using the chemical method. This method does not pose any danger, since the beneficial effect occurs due to chemical reactions, and not due to the ultra-high combustion temperatures of the reagent.

Special mention should be made of the observance of safety measures when carrying out all work related to the chimney. Do not fix chimney problems in windy weather! Try to use safety devices when working at height!

Troubleshooting structural problems

If certain features of the chimney design are identified that negatively affect the draft force, adjustments should be made to eliminate them. These actions include:

• dismantling several separate pipes and installing a single chimney channel;
• adding roof pipes to the required height;
• insulation of chimney elements, etc.

Ventilation arrangement

In some cases, traction may improve if drafts are avoided in the house or bathhouse. You can help with draft problems by installing ventilation devices on windows.

If there is no desired effect after all the methods described above, you should adopt modern devices to improve draft in the chimney.

Installation of devices

To improve the operation of the chimney, it is best to use special devices that allow you to regulate and control the draft. Such devices can be bought in a store or made with your own hands.

Fire safety rules for installing and using a potbelly stove

Compliance with fire safety rules when using a potbelly stove will protect all residents from possible unpleasant consequences:

• The fuel must be dry only; flammable mixtures must not be used;
• ignition is carried out by slightly opening the combustion damper, adding the required amount of combustible material and, directly, ignition;
• sufficient combustion of the fuel makes it possible to regulate the power level of the furnace device by closing or opening the ash compartment;
• Cleaning the furnace from accumulation of ash is carried out when the body has completely cooled, by pulling out the ash drawer and throwing out the contents.

We recommend that you familiarize yourself with the material on our website: “How to make potbelly stoves for a bath yourself.”

• the first use of a potbelly stove will be accompanied by the smell of melting paint, but in the future this episode will not occur;
• things that have a highly flammable composition should be located at a distance of 1 m from the stove;
• within one load, you cannot put more than 3 kg of dry fuel into the combustion compartment, while the door must be closed;
• It is strictly prohibited to use a potbelly stove when detecting any malfunctions in the operation of the chimney;
• Leaving a heater in working condition unattended with children present in the room is prohibited;
• during operation, the body of the potbelly stove becomes very hot, so you cannot touch it;
• The installation of the stove structure is carried out only on a special base (pedestal) with non-flammable properties.

Special devices for regulation

Modern instrument makers have taken care of producing special devices that regulate chimney draft:

1. Regulators. They are installed on the chimney outlet to normalize draft in the heating system, and also as a means of influencing the heating efficiency.
2. Deflectors. Such devices are fixed to the chimney from the outside. The draft speed is improved due to the fact that the diameter of this device is much larger than the chimney pipe, and, therefore, an area of ​​low pressure appears in it when air flows around it.
3. Chimney weather vane. It is a special design that performs several functions at once: improves traction, protects the pipe from raindrops and snow whirlwinds. The operation of the device is similar to the operation of a deflector; the thrust speed is normalized by reducing external air resistance.
4. Smoke fan. It is very popular among owners of houses with a heating system. An artificial air vortex is created inside the chimney due to the operation of the ventilation system, which requires electricity to connect. Compliance with all necessary safety measures is a prerequisite for the installation and operation of such a device to improve chimney draft.

All devices installed on the chimney pipe to improve draft require mandatory monitoring, especially in winter. This is due to the fact that additional devices attached to the chimney from the outside can become clogged, iced up (in winter) and thereby prevent the normal operation of the chimney. Blockage caused by devices can cause backdraft and the penetration of carbon monoxide into living spaces.

Do not forget to regularly inspect the chimney and devices that help increase draft.

Photo gallery: traction control devices

The most common device among stove heating users

This device is especially relevant for improving the operation of stoves and fireplaces.

Useful and beautiful device

By installing such a device, you can improve the performance of the entire heating system

Where to contact

Our company has been building baths and saunas for a long time, as well as selling the necessary materials for its production. If you need to buy a sauna stove, chimneys, boilers and other devices, then you will find it all in the store catalog.

However, we note that building a turnkey bathhouse is much more economical and simpler than buying a ready-made solution with the same configuration and equipment that we offer. Why? Firstly, the service life of our stoves is much longer, secondly, you save part of the budget, and thirdly, our specialists have extensive experience behind them, they know all the nuances of the correct selection of chimneys for the stove, masonry and installation. We offer the most favorable conditions and guarantee reliable work.

Solving problems yourself

Let's try to make the heating process safe and efficient with our own hands. The most common way to combat soot accumulation in pipes is with a brush and a sinker.

Cleaning the pipe with a brush

First, let's prepare everything you need:

1. A hard bristle brush. The diameter of this device is selected taking into account the cross-section of the pipe (from fifty to three hundred millimeters).
2. A thin metal cable (can be replaced with a very strong rope or rope).
3. Weight for hanging from a brush.

This is what a device for cleaning a chimney pipe looks like

Do not start work if there is strong wind or too much humidity outside. Try to think through and use reliable insurance to protect yourself from unforeseen events.

The ruff is weighted using a sinker, attaching it to the bottom of the device. The brush itself is hung on a cable. All fastenings must be especially reliable, otherwise the structure will fall apart and you will have to perform additional actions - to “fish” them out of the pipe.

First, all inspection holes in the chimney are cleaned, and then they begin to clean the pipe itself. By making a few up and down motions, you can get rid of any soot that will fall from the chimney into the furnace. It is best to have someone else around the stove to signal efficiency and when to stop working.

Cleaning the pipe should be completed when the soot stops falling out.

You can also clean the pipe using improvised means, about which many videos have been made.

Video: cleaning a pipe with improvised means

Selection of devices for regulation

Let's consider some characteristic features and methods of using devices for monitoring and adjusting traction.

Deflectors

Such structures are installed on the chimney (at its very top) to create obstacles to air flow. The intensity of the wind force drops noticeably when encountering such devices placed on a pipe. The smoke escapes through the channel “to freedom” due to weak air currents entering the pipe. These flows “catch” the exhaust gases and “push” them out.

Deflectors eliminate the possibility of pipe clogging, and, if made with taste, they significantly improve the appearance of the entire building.

There are several types of deflectors:

• TsAGI;
• round Wolpert;
• Grigorovich;
• plate-shaped;
• in the form of the letter H;
• rotating;
• vane.

Almost all of these devices are made from stainless steel, in rare situations - from copper. Using brackets, clamps, bolts, sealing tape, the deflector is attached to the chimney pipe. Some devices are also equipped with additional functions: to extinguish sparks (to eliminate a possible fire in the roof), to control the temperature of the exhaust air (in this case, the sensor is triggered if hot air does not come out and there is a possibility of reverse draft).

The disadvantages of using deflectors are their minimal effectiveness in calm weather.

Photo gallery: types of deflectors

The most common device for improving traction

Such a device can be purchased in specialized stores

The choice of device depends on the design features of the pipes and your preferences

Rotary devices

Turbines installed at the head of the chimney use the energy capabilities of the wind. Air flows set the rotary nozzle in motion (it always moves in one direction), and thereby the air becomes rarefied near the chimney. The entry of any foreign objects and sediment into the chimney with a rotary pipe is completely excluded.

Rotary pipes have a big disadvantage, similar to the operation of a deflector. Their use on a windless day is ineffective.

If you do not have great abilities, buying such devices is not a problem.

Traction regulators

Such devices are a real find for residents of country houses, lovers of baths and fireplace gatherings. These devices are attached to the boiler chimney. They are equipped with a metal plate with a weight that balances it on one side. When the draft is good, the metal plate does not interfere with the free access of air into the chimney. With weak or reverse thrust, the metal plate serves as a kind of stupor.

The range limits for thrust are set by the consumer himself, the usual parameters are 10–35 Pa.

The device operates completely autonomously and does not require any electrical current.

External factors

If there are no problems with clogging, the structural of the furnace is correct, but there is still no draft, most likely the problems are related to weather conditions or other environmental factors:

• improper ventilation system;
• daily temperature and humidity patterns;
• air circulation.

how to improve draft in a potbelly stove

Fireplace design features.

Incorrect design of the fireplace can be a prerequisite for smoke in the room, this occurs in new fireplaces. Either the firebox is very large or very tall in relation to the chimney. The height of the chimney may be insufficient; try to increase its height.

Double-sided fireplaces are sensitive to drafts in the house, because it is recommended to install glass doors on them to avoid smoke.

How to increase traction with your own hands: homemade devices

Before you start building a deflector yourself, weigh your strengths, review the available materials, and only then get down to business.

Drawings and diagrams

To create a deflector with your own hands, you need to use diagrams and drawings. You can use ready-made ones, which are presented in large quantities on the Internet, or you can do it yourself, relying on data from ready-made diagrams and drawings.

Photo gallery: ready-made diagrams of traction devices

On the Internet you can find good help for constructing the device.

Carefully study the device diagrams and choose the one that suits you

The diagram shows the structure of this traction improvement device

The diagram shows the components of this device

If you decide to test yourself and save money at the same time, arm yourself with measuring instruments to determine the internal diameter of the chimney. Depending on this value, using the table as a guide, you can determine the necessary parameters for the height of the deflector and the width of the diffuser.

With an internal diameter of 120 mm, these parameters are respectively 144/240, for a diameter of 140 mm - 168/280; if the internal cross-section is 200, then 240/400; for a cross section of 400 mm, you will need a deflector height of -480 mm, and a diffuser width of 800 mm.

You can calculate the necessary parameters (for a specific pipe diameter) yourself using simple calculations. To determine the width of the diffuser, the internal diameter of the pipe must be multiplied by 1.2; We consider the width of the umbrella for protection to be -1.7 x d; We find out the total height of the structure if we multiply the size of the internal section by 1.7.

Having received all the dimensions, we make drawings for more accurate cutting. We draw diagrams on a sheet of Whatman paper or on the back of the remaining pieces of wallpaper.

It is best to construct a life-size drawing. So that when cutting, you can simply attach the cut paper parts to the steel sheet and not have to recalculate the data taking into account the scale of the drawing.

We stock up on materials and tools

Everything needs to be prepared in advance so as not to be distracted during work.

To make the deflector we will need:

• galvanized sheet with a thickness of at least half a millimeter, stainless steel can also be used;
• metal scissors;
• drill with different drill bits;
• device for setting rivets;
• hammer;
• pliers;
• clamps, nuts, bolts;
• marker (for transferring the drawing onto a metal sheet).

Preliminary stage

The preparatory work consists not only in drawing out the details of the device, but also in cutting them out and trying them on. All paper elements are fastened with paper clips or a stapler and applied to each other. If everything fits, then you can carefully remove the fasteners and straighten the templates.

Do not be negligent in the process of creating a deflector; try to think about your safety. To avoid injuring your hands and to protect your eyes, use gloves and special glasses prepared in advance.

Let's get started

So, everything is in place, we can get started!

A step-by-step description of the sequence of actions will help you:

1. We transfer the parts cut out of paper onto a galvanized sheet. We should get developments of the following elements: cap, diffuser, outer cylinder and stand.
2. Using metal scissors, carefully cut out all the components of the deflector. In places where the cuts are made, the metal is bent with pliers to a thickness of half a millimeter and “passed” with a hammer.
3. The diffuser, cap and cylinder blanks are rolled up and holes for fastening are drilled (if bolts are used). Connections are made using rivets or bolts; in exceptional cases, welding can be used (semi-automatic).
4. To attach the cap we prepare 3-4 strips of metal. The dimensions of the strips are 6 by 20 cm. The strips, folded at the edges and tapped with a hammer, must be bent in the shape of the letter P. On the cap, five centimeters from the edge, drill 3-4 holes and secure the metal strips with bolts.
5. The other ends of the galvanized strips must be attached to the diffuser, thereby “looping” the cap and diffuser.
6. We insert the resulting structure into the shell.

You can watch the video about how to build a TsAGI deflector with your own hands.

Integrated approach and technical solutions

increase the efficiency of a potbelly stove to the maximum level. For example, combine smoke circulation and pyrolysis combustion, add fins to the body and increase the length of the chimney. A potbelly stove with a fan is good on its own, but nothing prevents you from covering it with bricks. The implementation of the described methods also varies - it all depends on the materials available and the design of the furnace itself.

Hi all! So I decided to make a homemade stove with increased efficiency with my own hands, I suggest you look at step-by-step photos of making a potbelly stove.

So, I will make the side walls from a profile pipe 60 x 30 x 3 mm. In essence, this will be an air heat exchanger; air will be forced through it. I want to distribute the heated air using a corrugated pipe along the walls of the garage and heat it evenly.

Creation of a convection system (fins)

Increasing the efficiency of a potbelly stove with your own hands involves creating a convector. Natural convection improves heat removal and ensures quick heating of the room. By installing a stove with a convector in the garage, we will get an excellent heating device. Literally 15-20 minutes after ignition, a comfortable temperature will be established in the garage. Our task is the following - we need to create a convector that sucks in air from below and exhausts it from above.

The easiest way to increase efficiency is to equip your potbelly stove with a metal screen. It is a sheet of iron that wraps the stove on the sides and back like a shirt. The distance between the body and the sheet is from 3 to 5 cm. The sheet is welded onto metal spacers - make them from thin reinforcement. The result is a fairly simple convector. The only problem is that the area of ​​thermal energy dissipation will remain the same.

Fins will help increase the efficiency of a potbelly stove. It can be done:

• From a profile rectangular pipe 20x40 mm.
• Made from a U-shaped metal profile.
• From a traditional round inch pipe.

We scald the back and side walls with the selected material. This will help increase the dispersion area. At the same time, we will get an effective convector.